Signature Hardware PROVINCETOWN 948666 Скачать руководство пользователя страница 9

9

1.800.221.3379

16. If faucet leaks from spout, shut o� the water

supplies and replace the cartridge (1).

Note: 

Install cartridge (1) correctly for proper handle

rotation.

16. Si el grifo gotea en la llave, cierre las líneas de
suministro de agua y reemplace el cartucho (1).

Nota: 

Instale correctamente el cartucho (1) para

asegurar la rotación adecuada de la manija.

P R OV I N C E TO W N

PRESSURE BALANCE SHOWER SET

SET DE DUCHA DE PRESIÓN BALANCEADA PROVINCETOWN 

SKU: 948666, 948673

INSTALLATION

INSTALACIÓN

1. Screw nut (1) onto thread section of valve body. 

Insert the brass stem extension (2) to valve body. 

Tighten screw (3).

1. Atornilla la tuerca (1) en la sección roscada del cuerpo 

de la válvula. Coloca la extensión del vástago de latón (2) 

en el cuerpo de la válvula. Aprieta el tornillo (3).

2. Position escutcheon (1) on valve body with drain 

hole (2) at the bottom. Place handle onto the brass 

stem extension and tighten handle seat (3).

2. Coloca la placa decorativa (1) en el cuerpo de la válvula 

con el orificio de drenaje (2) en la base. Coloca la manija 

en la extensión del vástago de latón y aprieta el asiento 

de la manija (3).

3

2

1

3

1

2

1

Содержание PROVINCETOWN 948666












Отзывы: