SignalFire Wireless I/O Module Mini Скачать руководство пользователя | Manualshive

Страница: 6 / 10

background image

Rev 1.5

SignalFire Telemetry

6

Modes of Operation

The Wireless I/O Module Mini can be run in two software settable “system modes”:

Node

,

and

Point-to-Point

. The ToolKit has a Radio Mode dropdown that can be set to either

Node or Gateway. For the WIOM Minis to operate in Node mode, all WIOM Minis on the
network must be set to Node and they will communicate with a SignalFire Gateway. For Point-to-
Point, set one WIOM Mini to Gateway and one WIOM Mini to Node, on a network that has no other
devices.

Node Mode

In Node mode, the WIOM Mini will send its analog and digital inputs/outputs to the Gateway. All IO
and then be read/set from a PLC via Modbus.

Node Mode. The Gateway reads all inputs from all nodes, and can control any output of any node as commanded by a PLC

«
...
4
5
6
7
8
...
»

Содержание Wireless I/O Module Mini











Отзывы:

Нет отзывов

Похожие инструкции для Wireless I/O Module Mini

Бренд: ICP DAS USA Страницы: 5

Бренд: ICP DAS USA Страницы: 7

Бренд: salmson Страницы: 16

Бренд: RTS Страницы: 131

Бренд: Dhollandia Страницы: 69

Бренд: golmar Страницы: 36

Бренд: HIKVISION Страницы: 23

Hydro-Guard HG-4

Бренд: Mueller Страницы: 8

Бренд: ERA Products Страницы: 4

Бренд: FARFISA INTERCOMS Страницы: 32

Бренд: Infinity Страницы: 24

VIP-172L-BRASS/SS

Бренд: Valcom Страницы: 3

Бренд: hager Страницы: 73

Бренд: Walkera Страницы: 22

DIY Colour Video Doorphone SW244-CVD

Бренд: Swann Страницы: 2

Бренд: Stahl Страницы: 24

Бренд: Zazen Страницы: 8

Бренд: ICP DAS USA Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды