SIGMATEK CCP 521 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 38

SIGMATEK CCP 521 Скачать руководство пользователя страница 1

C-DIAS PROCESSOR MODULE

CCP 521

15.03.2016

Page 1

C-DIAS Processor Module

CCP 521

The  CCP  521  processor  module  runs  the  control  program  and
thereby  represents  an  essential  component  of  an  automation  sys-
tem.  The  internal  DC/DC  converter  powers  all  modules  on  a
C-DIAS module carrier.

The  CAN  bus,  an  Ethernet  interface  or  the  USB  device  (Mini  USB)
can be used as the online interface.

A  7-segment  display  and  2  status  LEDs  provide  information  on  the
actual status of the CPU.

For  program  updates,  the  integrated  USB  Host  interface  can  be
used  (USB  stick,  keyboard).  With  help  from  the  exchangeable  SD
card, the entire control program can be easily exchanged.

The  CCP  521  processor  module  is  designed  to  be  mounted  in  the
control cabinet.

With  the  integrated  VARAN  manager,  the  processor  module  offers  the  possibility  to  con-
struct  a  high-performance VARAN system to operate for example, decentralized I/O mod-
ules, drive systems or communication modules.

Compatibility

Completely PC-compatible. The CCP 521 works with standard PC BIOS and therefore no
SIGMATEK-specific BIOS is needed; the LASAL operating system in provided.

1
2
3
...
»

Содержание CCP 521







































Отзывы:

Нет отзывов