SIGMATEK CCP 521 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 38

SIGMATEK CCP 521 Скачать руководство пользователя страница 16

CCP 521

C-DIAS PROCESSOR MODULE

Page 16

15.03.2016

To enter the mode for setting changes, press and hold the SET button while the C-IPC is
booting.

When the following appears in the display:

the SET button can be released.

After releasing the SET button, the first menu appears in the display.

With  several  short  presses  of  the  SET  button,  it  is  possible  to  switch  through  the  various
menu  points.  By  pressing  the  SET  button  for  approximately  1.5  s,  the  menu  is  accessed
and the setting can be changed with short presses.

Once the desired changes are made, press the SET button for about 5 seconds to end the
process. If the changes are to be discarded, press the RESET button to restart the C-IPC.

The  settings  for  the  IP  address,  subnet  mask  and  gateway  are  hexadecimal,  whereas  in
the left and right digits, 0 - F must be entered separately. The switch occurs when the SET
button is pressed for about 1.5 s.

The  values  from  AUTOEXEC.LSL  are  used  as  the  standard  settings;  changes  are written
back to this file. Before this, the original content of the file is written to AUTOEXEC.BAK.

«
...
14
15
16
17
18
...
»

Содержание CCP 521







































Отзывы:

Нет отзывов