manualshive.com logo in svg

Sigma DA5315, Руководство пользователя

Поделиться
Скачать
Sigma DA5315 Скачать руководство пользователя страница 15

14810

 • 

January2005

 • 

Operation

Page

 

11

Output Channel Assignment

The  sub-menu item is used to configure the routing matrix of defined inputs to spe-

cific physical output connectors. This is located under the  main menu item.

V-FADES

The V-fade parameter enables the DA5315 to conceal AES framing errors that occur 
upstream due to asynchronous switching or signal interruptions. With V-fade enabled, fast 
error transitions (clicks and pops) are eliminated.

V-fades can be enabled through the  menu item in Set-up.

OUTPUT SYNCHRONIZATION

The internal reference signal used for output synchronization is introduced into the frame 
through a connector on the rear panel of the S5000 Signal Management System frame 
labeled Video Reference. This reference is distributed throughout the frame by the CI5705 
Communications Interface located above the power supplies. The reference signal can be 
any valid NTSC or PAL video signal or AES Digital Audio. The DA5315 will match its ouptut 
signal timing to be synchronized to this reference.

To have the DA5315 match its output signal timing to the internal reference the  
menu setting must be set to ON. The Display Units setting (see Delay Display above) may 
be changed to display delay in units that are consistent with the internal reference format.

OctaBus™ ID Assignment

To accurately identify the signals being put onto the OctaBus™ from multiple modules hav-
ing eight outputs, each module must have a unique module ID. This module ID is defined 

via the  menu selection which is available as a submenu from the  main menu 
item. The default ID for unconfigured modules is (1). If Octabus is not enabled or is not 
being utilized, multiple modules in a system having identical Octabus ID’s is acceptable.

Anytime the channel designation requires an OctaBus™ ID, the display will show a decimal 
between the last two characters - the next to last character being the OctaBus™ ID and the 
last character being the channel number on the module specified by that OctaBus™ ID.

Reset Type/Initiation

Occasionally it may be necessary, or convenient, to clear the data stored in memory by 
resetting the DA5315. Because it may be desirable to erase only some of the data, there 

Содержание DA5315






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды