manualshive.com logo in svg

Sigma DA5315, Руководство пользователя

Поделиться
Скачать
Sigma DA5315 Скачать руководство пользователя страница 10

14810

 • 

January2005

 • 

Operation

Page

 

6

OPERATION

Front Panel Controls/Displays

The front panel, shown below, has three distinct functional areas - the Indicator LED’s 
under the OctaStream logo on the right side; the switch controls, mostly on the left side and 
the 7-segment display in the middle.

INDICATOR LED’S

LED’s are visible from the exterior of the frame when the front door is installed to accom-
modate checking the status of the modules without affecting the operating conditions within 
the frame. The LED’s provide information about the status of three operating conditions - 
error status, OctaBus™ status and power bus status.

1. ERROR - When this red LED is illuminated an invalid operating condition exists 

within the DA5315. These errors fall into three categories - power-on self-test 
failure, missing inputs or problems with the OctaBus™.

a.

Power-On Errors - cycle the power to the unit. It is recommended that the unit 
be left unpowered for a minimum of 5 seconds before reinitializing to allow all 
residual power to drain from the circuits assuring a complete reset of all 
functions.

b.

Missing Inputs - The Error LED will illuminate when either the input specified 
for a given output is unavailable or the defined reference signal is not 
present. To relieve this condition for unused ouputs, disable output error 
reporting using the  menu selection under the  main menu item.

c.

OctaBus™ - If there are problems with the signal on the OctaBus the ERROR 
LED will be illuminated and error messages can be accessed via the 
Diagnostic menu.

2. OCTABUS - This green LED indicates the presence of a valid signal connected to 

the OctaBus™ input BNC.

3. POWER - This green LED indicates the presence of suitable power being supplied 

to the module by the power supply in the S5000 frame.

Содержание DA5315






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды