SIGLENT TECHNOLOGIES SDG800 Series Скачать руководство пользователя страница 5

Страница: 5 / 128

SDG800 User Manual IV

If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

This product has been tested to the requirements of

CAN/CSA-C22.2 No. 61010-1, second edition, including Amendment 1,

or a later version of the same standard incorporating the same level of

testing requirements.

Not to use the product for measurements within other measurement

categories, such as CAT II, CAT III, CAT IV.

Not to use the equipment for measurements on mains circuits, not to

use the equipment for measurements on voltage exceed the voltage

range describe in the manual.

Only probe assemblies which meet the manufacturer’s specifications

shall be used.

The Responsible body or operator should refer to the instruction

manual to preserve the protection afford by the equipment. If the

equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

Any parts of the device and its accessories are not allowed to be

changed or replaced, other than authorized by the manufacturer of his

agent.

Содержание SDG800 Series

































































































































Результаты поиска

Содержание SDG800 Series

Отзывы:

Похожие инструкции для SDG800 Series

Бренды по названию

Популярные бренды

SIGLENT TECHNOLOGIES SDG800 Series, Руководство пользователя

Результаты поиска

Содержание SDG800 Series

Отзывы:

Похожие инструкции для SDG800 Series

Бренды по названию

Популярные бренды