manualshive.com logo in svg

Sigineer Power M12048D, Руководство пользователя

Поделиться
Скачать
Sigineer Power M12048D Скачать руководство пользователя страница 7

                                                                                                                                            www.sigineer.com 

7 

7. Negative Battery Terminal 

8. Positive Battery Terminal 

9. Dry Contact For AGS 

10. RS485/Remote Panel Port 

11. AC Input Breaker 

12. AC Output Breaker 

13. PV Input Terminal 

14. AC Output Terminal 

15. AC Input Terminal 

16. BMS Port 

17. Wi-Fi/GPRS Remote Module Port 

18.USB Port (Connects To Computer) 

19. DC Fan 

20. Grounding Terminal 

 

2.3 Features 

*Automatic Solar Charging When the Inverter is Powered Off 
*Auto Generator Start 
*Smart remote monitor with Wi-Fi or GPRS Module 
*Manual 50Hz/60Hz output frequency switch for worldwide operation 
*Maximum THD: 3% at nominal battery voltage 
*Powerful 4-stage power factor corrected battery charger up to 100 Amps, settable from 0%-100% 
*High surge output capability, 300% peak load for 5 seconds 
*Ultra low quiescent current, low power ‘Power Saver Mode’ to conserve energy 
*Equilization Charging 
*10 ms transfer time from AC to battery for the continuous load operation 
*Thermally controlled variable speed fan for more efficient cooling 
*Extensive protections against various harsh situations 
*Solar Priority or SBU developed for renewable energy systems 

 

2.4 Electrical Performance 

2.4.1 Invert 

Topology 

The M Series pure sine wave inverter/charger is built according to the following topology. 

⚫

 

Invert: Full Bridge Topology. 

⚫

 

Charge: Isolated Boost Topology 

When operating in invert mode, the direct current (DC) that enters the inverter from the batteries is filtered 
by a large input capacitor and switched “On” and “Off” by the Metal Oxide Silicon Field Effect Transistors 
(MOSFET) at a rate of 50 Hz or 60Hz and directed into the transformer which steps the voltage up to 230 or 
120 volts. The unit has a powerful microprocessor to control the output voltage and frequency as the DC 
input voltage and/or output load varies. 
Because of high efficiency MOSFETs and the heavy transformers, it outputs PURE SINE WAVE AC with 
an average THD of 7% (min 3%, max 10% under full linear loads) depending on the load connected and 
battery voltage. 
The peak invert efficiency of M Series is 85%. 
The inverter must be connected to batteries to power on. 
 

Overload Capacity 

1 For 100%<Load<120%, Fault (Power off) after 10 seconds. 
2 For 120%<Load

≤

300%, Fault (Power off) after the 5 seconds. 

 

Soft Start in Inverter Mode 

Содержание M12048D








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды