SIG 3D MAYHEM ARF, Инструкция по сборке, Страница: 2 / 22

Threadlock Compound, such as Loctite ® Non-Permanent Blue
Silicone Sealer - clear or white
Screwdriver Assortment
Pliers - Needle Nose & Flat Nose
Diagonal Wire Cutters
Small Allen Wrench Assortment
Drill with Assorted Drill Bits
Pin Vise for Small Dia. Drill Bits
Hobby Knife With Sharp #11 Blades
Scissors
Covering Iron and Trim Seal Tool
Masking Tape
Paper Towels
Power Drill With Selection of Bits
Dremel
® Tool with Selection of Sanding and Grinding Bits
Soldering Iron and Solder
Large Fuel Tubing
KIT CONTENTS INVENTORY:
The following is a complete list of all parts contained in this kit.
Before beginning assembly, we suggest that you take the time to
inventory the parts in your kit, using the check-off boxes (
❑
)
provided. Note that the CA type hinges for the ailerons, rudder,
and elevators are in place in each of these parts but are not yet
glued in place. Also, note that the nuts and bolts required to mount
your engine to the motor mounts are not included in this kit and
must be purchased separately.
Note: The “PWA” designation for some of the bolts and screws in
the following list means it has a “Phillips Washer Head”.
BASIC AIRCRAFT PARTS (covered with Oracover ):
1 bag
❑
(1) Right Wing Panel & Right Aileron, with
❑
(6) CA Hinges installed but not glued
1 bag
❑
(1) Left Wing Panel & Left Aileron, with
❑
(6) CA Hinges installed but not glued
1 bag
❑
(1) Fin & Rudder Set, with
❑
(3) CA Hinges installed but not glued
1 bag
❑
(1) Stabilizer & Elevator Set, with
❑
(6) CA Hinges installed but not glued
1 bag
❑
(1) Fuselage, with
❑
(1) Clear Plastic Canopy installed
❑
(4) M2 x 8mm PWA Mounting Screws, for canopy
❑
(2) 1/4-20 Blind Nuts installed, for wing attachment
❑
(3) M4 Blind Nuts installed, for l.g. attachment
❑
(1) Plastic Antenna Tube installed
1 bag
❑
(1) Fuselage Bottom Fairing
OTHER PARTS:
1 bag
❑
(1) Fiberglass Cowling, white
❑
(4) M2.6 x 10mm PWA Mounting Screws
1 bag
❑
(1) Right Fiberglass Wheel Pant, white
❑
(1) Left Fiberglass Wheel Pant, white
1 bag Main Landing Gear Parts:
❑
(1) Aluminum Landing Gear
❑
(3) M4 x 15mm PWA Mounting Bolts
❑
(2) M4 x 34mm PWA Axle Bolts
❑
(2) M4 Lock Nuts
❑
(4) M4 Hex Nuts
❑
(2) 2-3/4" dia. Main Wheels
❑
(4) M3 x 10mm PWA Mounting Bolts, for wheel pants
❑
(4) M3 Split Lock Washers, for wheel pants
1 bag Tailwheel Assembly:
❑
(1) Leaf-Spring with Steering Arm, Yoke, & Tailwheel
❑
(3) 3mm x 10mm PWA Mounting Screws
❑
(2) Coil Steering Springs
❑
(1) Metal Rudder T-Horn
❑
(2) 2mm x 9mm PWA Mounting Screws, for T-Horn
1 bag Fuel Tank Assembly:
❑
(1) 450cc (15.2 oz.) Plastic Tank
❑
(1) Rubber Stopper
❑
(1) Metal Front Clamp
❑
(1) Metal Rear Clamp
❑
(1) M3 x 18mm Clamp Bolt
❑
(1) Metal Clunk Pickup
❑
(1) Fuel Pickup Tubing, for inside tank
❑
(1) 3mm od x 40mm long Aluminum Tube
❑
(1) 3mm od x 47mm long Aluminum Tube
❑
(1) 3mm od x 60mm long Aluminum Tube
❑
(1) .093" id x .195" od x 9" Fuel Tubing
❑
(1) .093" id x .195" od x 9" Fuel Tubing
1 bag 2-3/4" Dia. White Spinner Assembly:
❑
(1) Plastic Spinner Cone
❑
(1) Plastic Spinner Backplate
❑
(1) Plastic Prop Shaft Adapters
❑
(4) Screws
1 bag
❑
(2) Glassed-Filled Engine Mounts
❑
(4) M4 x 25mm PWA Mounting Bolts
❑
(4) M4 Blind Nuts
❑
(4) M4 Flat Metal Washers
❑
(4) M4 Split Lock Washers
1 bag Throttle Pushrod Assembly:
❑
(1) 1/8” od x 15-3/4” Plastic Pushrod Tube
❑
(1) 3/16” od x 13-3/4” Plastic Pushrod Sleeve
❑
(1) Threaded Stud with Metal R/C Link, for servo end
❑
(1) Threaded Stud with Nylon R/C Link, for eng. end
❑
(2) Laser-Cut Plywood Pushrod Supports
1 bag Aileron & Elevator Pushrods:
❑
(3) 4-40 x 3” Threaded Pushrods
❑
(6) 4-40 Metal R/C Links
❑
(6) 4-40 Hex Nuts
❑
(6) Spring Keepers
1 bag Misc. Control System Parts:
❑
(2) .023" dia. Steel Cables,
for pull-pull rudder linkage
❑
(4) Rigging Couplers w/ R/C Link & Knurled Stop Nut,
for pull-pull rudder linkage
❑
(4) 2mm od x 4mm Metal Tubes,
for pull-pull rudder linkage
❑
(3) Right Control Horns,
for elevator(1), aileron(1), rudder(1)
❑
(2) Left Control Horns,
for aileron(1), rudder(1)
❑
(12) 2.6mm x 10mm Mounting Screws,
for aileron & elevator control horns
❑
(4) M2.5 x 14mm Mounting Bolts,
for rudder control horns
❑
(4) M2 Hex Nuts, for rudder control horns
❑
(4) M2.5 Split Lock Washers,
for rudder control horns
1 bag Misc. Parts:
❑
(1) Hardwood Front Wing Joiner
❑
(2) 1/4-20 x 2" Nylon Wing Bolts
❑
(2) Fiberglass Wing Bolt Guides
❑
(1) Plywood Wing Bolt Plate
❑
(1) 3/8" x 1/2" x 4" Balsa Stick,
for fuel tank rear support
MISCELLANEOUS:
❑
1 EACH #SIGDKM279 3D MAYHEM Decal Sheet
❑
1 EACH #SIGIB279 3D MAYHEM Assembly Manual
2
®