manualshive.com logo in svg

Sig Marine Sig200, Руководство по эксплуатации и установке

Поделиться
Скачать
Sig Marine Sig200 Скачать руководство пользователя страница 25

 

 

25 

13. Flooding the Burner

 

A vaporizing oil burner of this type can be flooded if care is not taken to prevent 
excess  oil  entering  the  burner  when  lighting.      By  following  the  lighting 
instructions  flooding  will  be  avoided.  A  flooded  burner  that  is  still  burning 
should be turned off and the heater monitored until the oil has burned off. Use 
the combustion assist fan to add air to fully combust the excess fuel.  

Reasons that will flood your burner. 

 

Increasing  the  fuel  supply  too  quickly  without  use  of  the  combustion 
assist fan. 

 

Poor draft and/or ventilation. 

The  suggested  method  to  fix  a  flooded  burner  is  to  sacrifice  a  toilet  paper 
roll as a perfectly fitted sponge and then dispose of the oil soaked roll. For 
this reason, always monitor the heater closely when lighting. 
 

DANGER: This oil must be removed from the pot before the heater is lit 
again or the stove will dangerously overheat. 

 
If the flame has extinguished, the oil metering will continue to deliver fuel to 
the burner causing it to accumulate fuel to a level of 5/8” from the bottom of 
the burner and no more for 6” burners (Bristol, Bering, Adriatic and Pacific). 
The 7” burners (Atlantic and Beaufort models) with a accumulate 1” of fuel 
from the bottom of the burner. Never relight this amount of fuel. 
 
 
 
 
 
 
 

 
 
 
 
 
 

Содержание Sig200










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды