Sierra Wireless mangOH Green DV4 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 39

Sierra Wireless mangOH Green DV4 Скачать руководство пользователя страница 39

Software Setup

Rev 3 Nov.16

39

4118902

•

Ports [COM & LPT] > Sierra Wireless NMEA Port (This is the port that you will
use to communicate with the module from your terminal emulator.)

Install a Terminal Emulator

To communicate with the mangOH Green, you need to use a terminal emulator
program such as Tera Term or HyperTerminal

®

.

When you have an emulator installed, use it to establish a console connection to the
mangOH Green:

•

Port—Serial modem COM port (for Sierra Wireless devices, this is the Sierra
Wireless NMEA Port)

•

Baud rate—115200

Install the Arduino IDE

To work with the mangOH Green‘s integrated Arduino-compatible circuit, you must
download and install the Arduino IDE (Integrated Development Environment). The
IDE is used to write code (‘sketches’) and upload them to the mangOH Green’s
integrated Arduino-compatible circuit. Installation and usage information is available
at

Install the Legato Developer Studio

To create Legato applications for the CF3 module, download and install the Open AT
Developer Studio (a Legato IDE) available at

Download Firmware Updates

Firmware updates will be made available for download from

.

Write Your First Program

For instructions on building applications (including writing a ‘Hello World’ program to
test your mangOH Green), and to download sample Arduino sketches and Legato
applications, visit

.

«
...
37
38
39

Содержание mangOH Green DV4








































Отзывы:

Нет отзывов