Sierra Wireless mangOH Green DV4 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 39

Sierra Wireless mangOH Green DV4 Скачать руководство пользователя страница 17

Hardware Setup and Operation

Rev 3 Nov.16

17

4118902

Connect Battery Backup

Optionally, you can connect a rechargeable Li-Ion/Li-Polymer battery to the mangOH
Green to provide uninterrupted power in the event that the primary power supply (DC
or USB) fails.

If a jumper is placed on CN1201, the mangOH Green recharges the battery and then
provides a trickle charge to maintain the battery’s full charge.

To connect a rechargeable Li-Ion/Li-Polymer battery to the mangOH Green:

1.

Connect the battery to CN1202.

Figure 3-9: Battery Backup (CN1202/CN1203)

Figure 3-10: mangOH Green With Rechargeable Battery Connected

2.

If you want the battery to recharge while connected to the board, place a jumper
across the pins on CN1203 (Recharge select).

Caution:

If a rechargeable battery is not connected to the board, make sure to remove the

jumper from CN1203.

1—Recharge select (CN1203)
2—Rechargeable battery connector (CN1202)

1—Jumper on Recharge select (CN1203)
   Battery recharges when mangOH Green
   is powered by DC or USB.
   (DC power shown)

-/+ —Negative and positive terminals of
rechargeable battery connector (CN1202)

«
...
15
16
17
18
19
...
»

Содержание mangOH Green DV4








































Отзывы:

Нет отзывов