Sierra Wireless mangOH Green DV4 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 39

Sierra Wireless mangOH Green DV4 Скачать руководство пользователя страница 38

Rev 3 Nov.16

38

4118902

4

4: Software Setup

This chapter describes software resources that you will need on your computer to
access the mangOH Green and develop applications for its CF3 module and
integrated Arduino-compatible circuit.

Sample applications and instructional materials are available from the sites
mentioned in this chapter. For detailed information on developing for the mangOH
Green, see the mangOH Green Developer’s Guide and related documents (available
from

).

Install / Update Windows Driver

If you are using a Windows computer, you will need to install the Legato driver for the
CF3 module that you install in your mangOH Green.

1.

to download the Windows driver and driver installation instruc-

tions for your CF3 module.

2.

Install the Windows driver.

3.

When the mangOH Green is connected via USB to the computer, display the
Device Manager (Control Panel > System > Device Manager).

Figure 4-1: Windows Device Manager

If the driver installed correctly, you will see the following items listed:

•

Modems > Sierra Wireless WWAN Modem (This is the module in socket J200.)

•

Ports [COM & LPT] > Sierra Wireless DM Port

«
...
36
37
38
39
»

Содержание mangOH Green DV4








































Отзывы:

Нет отзывов