Sierra Wireless AirLink FX100 Скачать руководство пользователя

Страница: 9 / 114

4112221

Rev 7.2

June 19, 2013

User Guide

15.1.

Certification Compliance.................................................................................................. 97

15.1.1.

UL Listed .................................................................................................................. 98

15.2.

Applicable Standards Listing ........................................................................................... 98

16.

SAFETY RECOMMENDATIONS ..................................................................... 100

16.1.

General Safety ............................................................................................................... 100

16.2.

Vehicle Safety ................................................................................................................ 101

16.3.

Care and Maintenance .................................................................................................. 101

16.4.

Your Responsibility ........................................................................................................ 101

17.

REFERENCE DOCUMENTS ............................................................................ 102

17.1.

Firmware Documentation .............................................................................................. 102

17.2.

X-card Documentation ................................................................................................... 102

17.3.

Firmware Upgrade Documentation ............................................................................... 102

18.

LIST OF ABBREVIATIONS ............................................................................. 103

19.

PACKAGING .................................................................................................... 106

19.1.

Contents ........................................................................................................................ 106

19.2.

Accessories Description ................................................................................................ 106

19.2.1.

GSM Antenna ......................................................................................................... 106

19.2.2.

GPS Antenna ......................................................................................................... 107

19.2.3.

Serial Data Cable ................................................................................................... 107

19.2.4.

USB Cable.............................................................................................................. 108

19.2.5.

6-wire Cable Accessory used with the FX Series .................................................. 108

19.2.6.

Package ................................................................................................................. 108

19.2.7.

Two Holding Bridles ............................................................................................... 108

19.2.8.

Power Supply used with the FX Series .................................................................. 109

20.

PRODUCT LABELING ..................................................................................... 110

21.

SAFETY RECOMMENDATIONS (FOR INFORMATION ONLY) ..................... 111

21.1.

RF Safety ....................................................................................................................... 111

21.1.1.

General ................................................................................................................... 111

21.1.2.

Exposure to RF Energy .......................................................................................... 111

21.1.3.

Efficient Terminal Operation................................................................................... 111

21.1.4.

Antenna Care and Replacement ............................................................................ 112

21.2.

General Safety ............................................................................................................... 112

21.2.1.

Driving .................................................................................................................... 112

21.2.2.

Electronic Devices .................................................................................................. 112

21.2.3.

Vehicle Electronic Equipment ................................................................................ 112

21.2.4.

Medical Electronic Equipment ................................................................................ 112

21.2.5.

Aircraft .................................................................................................................... 113

21.2.6.

Children .................................................................................................................. 113

21.2.7.

Blasting Areas ........................................................................................................ 113

21.2.8.

Potentially Explosive Atmospheres ........................................................................ 113

Содержание AirLink FX100



















































































































Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды

Sierra Wireless AirLink FX100, Руководство пользователя

Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды