background image

1

Safety instructions     

– The washing machine is heavy - take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not install the washing machine outdoors or in 

areas where there is a risk of frost.

– The washing machine may be damaged. Do not lift by projecting components (e.g. washing 

machine door).

– In addition to the instructions mentioned here, special regulations of the relevant water and 

power supply companies may apply.

– If in doubt, have the appliance connected by a technician.
– Lay hoses and cables in such a way that there is no risk that they can be tripped over.

Environmental disposal

– Dispose of packaging in an environmentally friendly manner.
– This appliance has been identified in accordance with the European Directive 2002/96/

EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive specifies a 
framework for the return and recycling of waste appliances and is valid throughout Europe.

Scope of delivery 

according to model

Humidity in the drum is

caused by the final inspection.

Depending on the connection

– A 24-40 mm dia. hose clip may also be required for connecting the siphon (available from 

specialist retailers) 

a

page 4:

Water connection.

 Useful tool

– Spirit level for aligning the washing machine.

Water drainage

Elbow

for fixing the waste 
water hose

Aqua-Stop

Aqua-Secure

Standard

Power cord

Water supply

Covers

Hose holder

2

Hose and cable lengths 

depending on model

   

Installation area

– Stability is important to prevent the machine from wandering.
– The installation area must be firm and level.
– Soft floors/floor coverings such as e.g. carpets are not suitable. 

If installing the appliance on a wooden joist floor

– If possible, install the washing machine in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is 

essential 

to secure the washing machine feet with holding brackets*. 

*order no. WMZ 2200, WX 9756

Connection on left side

or

Connection on right side

Note

: if hose holders are used, the hose lengths may be reduced. 

Available from dealer/customer service:
– Aqua-Stop extension hose**, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard model. 

**order no. WMZ 2380, WZ 10130

Built-under/Built-in appliance

Build-under/build-in before connection to the power supply.

Installed in between kitchen units (built-under or built-in)

– 60 cm cavity width required.
– Install washing machine only under a continuous worktop that is connected firmly to the 

adjacent cupboards.

~

135 cm

m

a

x

1

0

0

 c

m

~

100 cm

~

95 cm

~

140 cm

~

160 cm

~

165 cm

a

Содержание WLM20460BY







Отзывы: