Siemens SPCK420 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

background image

SPCK420/421/422 LCD-Keypad - User Manual

User programming via the keypad > Setting and unsetting the system > CODED RESTORE

CODED RESTORE

The feature provides the user with the ability to restore alert conditions that would normally only be available to the
installation engineer. To provide the user with this ability, it is necessary to protect this feature with a code.

To perform a coded restore on the system:

The security grade of the system must be set to Grade 3 or Unrestricted.

Ensure that the zone or fault that caused the alert condition has been physically restored to its normal operating
state.

Contact the installer before entering user programming and selecting the coded restore feature. The contact details
of the installer should be available from the drop down label beneath the keypad.

Press SELECT on the

Coded Restore

option.

1.

A 6 digit reset code displays on the top line.

Provide 6 digit code to installer.

2.

Receive newly generated code from installer.

3.

Enter new code at the AUTH CODE prompt.

4.

Press SELECT.

5.

The message SYSTEM RESTORED displays on the top line of the display.

© Siemens Industry - 11-24-2009

«
...
26
27
28
29
30
...
»

Содержание SPCK420





















































Отзывы:

Нет отзывов

Похожие инструкции для SPCK420

Navigator -M1KPNAV

Бренд: Elk Страницы: 2

Бренд: CADDX Страницы: 6

CONLAN CM1000EMV

Бренд: Salto Страницы: 23

Бренд: DS Страницы: 2

Бренд: DS Страницы: 4

Бренд: POSIFLEX Страницы: 13

A-100 - A-100IMWP

Бренд: Alarm Lock Страницы: 2

HomeTec Pro CFT3000

Бренд: Abus Страницы: 96

Бренд: Radionics Страницы: 2

Бренд: Eaton Страницы: 4

ABB ACS355 THREE-PHASE VFD

Бренд: Patterson Страницы: 3

Бренд: Black Nova Страницы: 24

OptionFinder Micro Plus

Бренд: Option Technologies Страницы: 9

SuperBus 2000 2X16

Бренд: Interlogix Страницы: 4

Бренд: Interlogix Страницы: 4

Бренд: Interlogix Страницы: 14

CryptiX PINPad RE652 Series

Бренд: Resolution Страницы: 2

VMX-synergy VMX-SGY-010

Бренд: motortronics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды