Siemens SPCK420 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 52

background image

SPCK420/421/422 LCD-Keypad - User Manual

User programming via the keypad > Setting and unsetting the system

Setting and unsetting the system

For each menu option, the keypad must be in User programming:

Enter a valid User code (default 2222).

1.

To select a programming option, use the up/down arrow keys or enter the digit listed in the table below.

2.

1
UNSET
Performs an Unset on the system. If multiple areas are defined then each area is presented in a sub-menu. For a single
area system this option is only presented when the system is Set.
2
FULLSET
Performs a Fullset on the system. If multiple areas are defined then each area is presented in a sub-menu. For a single
area system this option is only presented when the system is Unset.
3
PARTSET A
Performs a Partset A on the system. If multiple areas are defined then each area is presented in a sub-menu.
4
PARTSET B
Performs a Partset B on the system. If multiple areas are defined then each area is presented in a sub-menu.

Further information

UNSET
FULLSET
PARTSET
FORCE TO SET
RESTORE
CODED RESTORE

© Siemens Industry - 11-24-2009

«
...
20
21
22
23
24
...
»

Содержание SPCK420





















































Отзывы:

Нет отзывов

Похожие инструкции для SPCK420

Бренд: Knoll Страницы: 2

Бренд: Holtek Страницы: 2

Бренд: Automated Logic Страницы: 5

Бренд: urmet domus Страницы: 12

Бренд: NAPCO Страницы: 32

Бренд: Magellan Страницы: 2

Бренд: Parker Страницы: 32

Бренд: Alarm Controls Corporation Страницы: 32

Lyric LKP500-ENC

Бренд: Honeywell Страницы: 2

Бренд: Honeywell Страницы: 2

6160V - Ademco Talking Alpha Display Keypad

Бренд: Honeywell Страницы: 2

5828V - Ademco Wireless Talking Keypad

Бренд: Honeywell Страницы: 4

Zum Wireless Keypad

Бренд: Crestron Electronics, Inc. Страницы: 2

Premier Elite LCDLP-W

Бренд: Texecom Страницы: 13

Бренд: Protegus Страницы: 2

Бренд: Motostar Страницы: 10

Бренд: Luigs & Neumann Страницы: 14

Бренд: Ksenia Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды