manualshive.com logo in svg

Siemens SITRANS S7-300, Руководство пользователя, Страница: 14 / 16

Поделиться
Скачать
Siemens SITRANS S7-300 Скачать руководство пользователя страница 14

Planning/configuring 

 

3.1 Required steps 

 

Configuring a SmartLinx ready device with a PROFIBUS DP card in a S7-300 or S7-400 PLC 

14

 

Application examples, 08\2020, AG060425 

 

 

Note 

•

 

The input and output addresses that the software selected for the card will be needed 
later. Please record. 

•

 

The input and output sizes vary from product to product (and software revision). Please 
refer to the SmartLinx PROFIBUS DP manual for the details on the correct product sizes 
to use. 

 

Step 6 - Download the new configuration 

1.

 

Click the 

Save and Compile 

icon. 

 

2.

 

Click the 

Download

 icon to save the new configuration to the PLC. To do this you will have 

to place the PLC in stop mode. 

 

 

 

 

Note 

After the download is complete, do not place the PLC in run mode. 

 

3.

 

Connect the MultiRanger to the network and power the MultiRanger verifying that the 
network address is set correctly. 

4.

 

Place the PLC in 

RUN 

mode. The green light on the SmartLinx card will activate. 

Содержание SITRANS S7-300

















Отзывы:

Нет отзывов