Siemens SITRANS P 7MF4232 Скачать руководство пользователя страница 5

Страница: 5 / 38

7MF4232

Operating Instructions

C79000-B5676-C92-01

Contents

Page

Technical Description

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1

Range of Application

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2

How it works

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3

Technical Data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4

Ordering data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5

Dimensions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.1

Fixing with a mounting bracket

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.2

Turning the measuring cell in relation to the housing

. . . . . . . . . . . . . . .

2.2

Electrical connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3

Installing the analog indicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4

Turning the digital indicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Commissioning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1

Operation with PC/Laptop

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2

Operating from a HARTR-Communicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3

Operation on the transmitter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.1

General

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.2

Setting the start of scale and full scale with the cover closed without viewing
window and activated key disable

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3

Operation with visible digital display and deactivated key lock

. . . . . . .

4.3.3.1

Setting start of scale and full scale with a pressure source

. . . . . . . . . .

4.3.3.2

Setting start of scale and full scale without pressure transmitter

. . . . .

4.3.3.3

Correction of zero point

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3.4

Setting electrical damping

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3.5

”Loop check” function

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3.6

Output current in error situations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3.7

Disable pushbuttons and/or functions

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3.8

Select display (current, %, pressure)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3.3.9

Select engineering units

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4

Write protection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Conformance Certificates

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание SITRANS P 7MF4232







































Результаты поиска

Содержание SITRANS P 7MF4232

Отзывы:

Похожие инструкции для SITRANS P 7MF4232

Бренды по названию

Популярные бренды

Siemens SITRANS P 7MF4232, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS P 7MF4232

Отзывы:

Похожие инструкции для SITRANS P 7MF4232

Бренды по названию

Популярные бренды