Siemens SITOP PSU6200 Скачать руководство пользователя страница 11

Страница: 11 / 76

Description, device design, dimension drawing

2.3 Potentiometer

SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76

2.3

Potentiometer

The potentiometer

④

on the front of the device is used to adjust the output voltage. The

output voltage is set to the rated value at the factory and can be set within certain limits; for

example, to compensate voltage drops across long supply lines to the connected load.

Figure 2-4

Potentiometer

Type

Factory setting

Adjustment range

6EP3323-7SB00-0AX0
6EP3324-7SB00-3AX0

12 V

12 V - 15.5 V

6EP3333-7LB00-0AX0
6EP3333-7SB00-0AX0
6EP3334-7SB00-3AX0
6EP3336-7SB00-3AX0

24 V

24 V - 28 V

NOTICE
Thermal overload possible
When adjusting the output voltage to greater than the rated voltage, the output current must

be derated by 4 %/V (for devices with a rated output voltage of 24 V) and 8 %/V (for

devices with a rated output voltage of 12 V) – or the permissible ambient temperature must

be taken into account with 3 °C/V.

Note
It is only permissible to use an insulated screwdriver when actuating the potentiometer.

For information on actuating the potentiometer (screwdriver, torque), see Connections and

terminal designation (Page 10).

Содержание SITOP PSU6200













































































Результаты поиска

Содержание SITOP PSU6200

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITOP PSU6200, Руководство пользователя

Результаты поиска

Содержание SITOP PSU6200

Отзывы:

Бренды по названию

Популярные бренды