Siemens SITOP PSU300S Скачать руководство пользователя страница 53

Страница: 53 / 66

SITOP PSU300S
Manual, 12.2016, C98130-A7587-A1-7-7629

Applications

9.1

Parallel connection to increase the power rating

To increase the power rating, power supplies of the same type can be directly connected in

parallel.
The following must be observed:

●

The cables connected to each power supply at terminals "+" and "-" must have identical

lengths and the same cable cross-sections (or the same impedance) up to a common

external connection point (terminal strip) if possible.

●

The power supplies connected in parallel must be switched on simultaneously with a

common switch in the line feeder cable (e.g. with the main switch available in control

cabinets).

●

The output voltages measured in no-load operation for the power supplies that are not yet

connected in parallel should not deviate more than a maximum of 50 mV. This usually

corresponds to the factory setting. If the output voltage is changed, you should connect

the "-" terminals and then, in no-load operation, measure the voltage difference between

the "+" terminals that have not yet been connected. The voltage difference should not

exceed 50 mV.

Figure 9-1

Parallel connection

Note
It is not permissible to take into account simultaneous overload capability (Extra-Power

150% for 5 s/min) of several power supplies connected in parallel when configuring the

power supply system.

Содержание SITOP PSU300S



































































Результаты поиска

Содержание SITOP PSU300S

Отзывы:

Похожие инструкции для SITOP PSU300S

Бренды по названию

Популярные бренды

Siemens SITOP PSU300S, Руководство пользователя

Результаты поиска

Содержание SITOP PSU300S

Отзывы:

Похожие инструкции для SITOP PSU300S

Бренды по названию

Популярные бренды