Siemens SIMATIC NET RUGGEDCOM RST2228 Скачать руководство пользователя страница 24

Страница: 24 / 58

Installing the Device

2.5 Connecting Power

2.5

Connecting Power

The RUGGEDCOM RST2228P supports dual redundant AC and/or DC power supplies

that can be installed in any combination.
The RUGGEDCOM RST2228P can be equipped with either a screw-type or pluggable

terminal block, which provides power to both power supplies. The screw-type ter-

minal block is installed using Phillips screws and compression plates, allowing either

bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reli-

able connections under severe shock or vibration.

DANGER

Electrocution hazard – risk of serious personal injury or death. The device may have

two power supplies equipped, which may be connected to separate power sources.

Make sure all power sources are off before servicing the power supply terminals.

CAUTION

Electrical hazard – risk of damage to equipment. Do not exceed the power supply

voltage ratings for each power supply input. For example, if PS1 is a low DC power

supply, do not connect the PS1 terminals to a high AC/DC power source.

NOTICE

• A circuit breaker rated no higher than 20 A must be installed between the device

and the supply mains.

• Whenever possible, use a separate circuit breaker for each power supply.
• For maximum redundancy in a dual power supply configuration, use two inde-

pendent power sources.

• A socket outlet/disconnect device must be installed near the device and be easily

accessible.

• Equipment must be installed according to applicable local wiring codes and

standards.

2.5.1

Connecting High AC/DC Power

To connect a high AC/DC power supply to the device, do the following:

DANGER

Electrocution hazard – risk of death, serious personal injury and/or damage to

the device.

Make sure the supplied cover is always installed over high voltage screw-type termi-

nal blocks.

RUGGEDCOM RST2228P

Installation Manual, 12/2019, C79000-G8976-1403-05

Содержание SIMATIC NET RUGGEDCOM RST2228



























































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM RST2228, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды