Siemens SIMATIC NET RUGGEDCOM RST2228 Скачать руководство пользователя страница 18

Страница: 18 / 58

Installing the Device

This chapter describes how to install the device, including mounting the device, con-

necting power, and connecting the device to the network.

DANGER

Electrocution hazard – risk of serious personal injury and/or damage to equip-

ment.

Before performing any maintenance tasks, make sure all power to the device has

been disconnected and wait approximately two minutes for any remaining energy

to dissipate.

WARNING

Radiation hazard – risk of serious personal injury.

This product may contain a laser system and is classified as a

CLASS 1 LASER PROD-

UCT

. Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

NOTICE

This product contains no user-serviceable parts. Attempted service by unauthorized

personnel shall render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate

specifications, test results, and agency approvals, and void the user's authority to

operate the equipment.

NOTICE

This product should be installed in a

restricted access location

where access can only

be gained by authorized personnel who have been informed of the restrictions and

any precautions that must be taken. Access must only be possible through the use of

a tool, lock and key, or other means of security, and controlled by the authority re-

sponsible for the location.

2.1

General Procedure

The general procedure for installing the device is as follows:

NOTICE

The user is responsible for the operating environment of the device, including main-

taining the integrity of all protective conductor connections and checking equip-

RUGGEDCOM RST2228P

Installation Manual, 12/2019, C79000-G8976-1403-05

Содержание SIMATIC NET RUGGEDCOM RST2228



























































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM RST2228, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды