Siemens SIMATIC NET RUGGEDCOM RS400 Скачать руководство пользователя

Страница: 38 / 48

Technical Specifications

5.5 Serial Port Specifications

5.5

Serial Port Specifications

Port Type

Media

Distance

Connector Type

RS232

Standard RS232

Shielded Serial Cable

15 m (49 ft)

DB9

RS485

Shielded Twisted-Pair

1200 m (3937 ft)

Insulated Terminals

RS232/RS485/RS422

Shielded Twisted-Pair

1200 m (3937 ft)

DB9

RS232/RS485/RS422

Shielded Twisted-Pair

1200 m (3937 ft)

RJ45

5.6

Operating Environment

The RUGGEDCOM RS400 is rated to operate under the following environmental

conditions.

Ambient Operating

Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Storage Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Relative Humidity

5% to 95%

Maximum Altitude

2000 m (6562 ft)

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure.

Non-condensing.

5.7

Mechanical Specifications

Weight

2.2 kg (4.8 lb)

Ingress Protection

IP30

Enclosure

18 AWG Galvanized Steel

5.8

Dimension Drawings

Note

All dimensions are in millimeters, unless otherwise stated.

RUGGEDCOM RS400

Installation Manual, 01/2021, C79000-G8976-1016-11

Содержание SIMATIC NET RUGGEDCOM RS400

















































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RS400

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RS400

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM RS400, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RS400

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RS400

Бренды по названию

Популярные бренды