manualshive.com logo in svg

Siemens SIMATIC IOT, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMATIC IOT Скачать руководство пользователя страница 34

Expand device 

 

5.3 Install Mini PCIe card 

 

SIMATIC IOT2020, SIMATIC IOT2040 

34

 

Operating Instructions, 10/2016, A5E37656492-AB 

Procedure  

The following example describes the installation of a Mini PCIe WLAN card, including 

mounting of the antenna jacks. If you install a different Mini PCIe card, the work steps 4, 5 

and 7 are not required. 

 

When the enclosure is secured with 

two screws at the rear panel, remove 

the two screws. 
Remove the battery, see section 

"Replace the backup battery 

(Page 36)". 
Then follow these steps: 
1.

 

Loosen the front panel of the 

housing from the rear panel of the 

housing. Carefully press with the 

blade of a flat-blade screwdriver in 

the marked recesses and carefully 

pull on the appropriate place on 

the front panel of the enclosure. 

2.

 

Remove the front panel of the 

enclosure. 

3.

 

Remove the motherboard. 

4.

 

Drill the bushings for the antenna 

sockets with a corresponding 

diameter at the markings shown. 

5.

 

Install the antenna sockets in the 

enclosure. 

6.

 

Insert the Mini PCIe card in the 

Mini PCIe interface on the 

motherboard from below as 

illustrated. 

7.

 

Connect the antenna cables to the 

Mini PCIe card. 

 

 

Then install the motherboard again and close the housing. 

Содержание SIMATIC IOT

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды