Siemens SIMATIC IOT Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

background image

Installing and connecting the device

3.2 Mounting the device

SIMATIC IOT2020, SIMATIC IOT2040

24

Operating Instructions, 10/2016, A5E37656492-AB

3.2.2

Mounting on DIN rails

Requirement

●

A DIN rail, 35 mm standard profile
The DIN rail is installed at the installation site.

Procedure

Mounting

1.

Place the device and rail clip on the upper

edge of the standard profile rail at the

position shown and push the device down.

2.

Swing the rail clips of the device from

below via the standard profile rail.

3.

Push the device in the direction of the

standard profile rail. You will hear the

device click into place.

Removing
1.

Push down the device until it is released by the rail clips.

2.

Swing the device out of the standard profile rail.

3.

Lift the device up and off.

«
...
22
23
24
25
26
...
»

Содержание SIMATIC IOT

































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC IOT

Бренд: B&B Electronics Страницы: 60

Бренд: VBOX Страницы: 3

Бренд: AMPLIFIED ENGINEERING Страницы: 20

Бренд: AudioCodes Страницы: 5

Бренд: Grandstream Networks Страницы: 20

Бренд: AudioCodes Страницы: 70

WPC-832-2-Modbus-MQTT

Бренд: KSH International Страницы: 16

P-661HW-D Series

Бренд: ZyXEL Communications Страницы: 146

Бренд: OPW Страницы: 13

Бренд: Sony Страницы: 70

Бренд: Sony Страницы: 76

Бренд: Telos Страницы: 258

Бренд: Meraki Страницы: 11

Link Gate GSM ISDN

Бренд: Linkcom Страницы: 22

Бренд: Logic IO Страницы: 36

Бренд: Cell2Tel Страницы: 34

IO-Link Master 4-EIP

Бренд: Comtrol Страницы: 14

Бренд: Inovonics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды