background image

Technical specifications 

 

5.5 Ambient conditions 

 

IFP2200 INOX MT ETH 

38

 

Compact Operating Instructions, 03/2018, A5E42185570-AA 

Testing mechanical ambient conditions  

The table below provides information on the type and scope of tests for mechanical ambient 

conditions. 

 

Tested for 

Test standard 

Comments 

Vibrations 

Vibration test in accordance 

with IEC 60068, part 2-6 

(sinusoidal) 

Type of vibration: 
Frequency cycles at a rate of change of  

1 octave/minute. 
10 ... 58 Hz, constant amplitude 3.5 mm 
58 ... 200 Hz, constant acceleration 1 g 
Vibration duration: 
10 frequency cycles per axis in each of the three 

mutually vertical axes 

Shock  

Shock test in accordance 

with IEC 60068, Part 2-27 

Type of shock: Half-sine 
Severity of shock: 
Peak value 15 g, duration 11 ms 
Direction of shock: 
3 shocks in ± direction of axis in each of the three 

axes vertical to each other 

Shock pulses within the specified range can be transferred to the display but do not impact 

the functionality of the device. 

Climatic ambient conditions  

The following table shows the climatic ambient conditions for operation of the device. 

 

Ambient conditions  

Permitted range  

Comments 

Temperature 

 

 

 

Vertical mounting 

0 ... 45 °C (landscape format) 
0 ... 40 °C (portrait format) 

 

 

Mounting at an angle  0 ... 40 °C (landscape format) 

0 ... 35 °C (portrait format) 

Slope angle max. 35° 

Relative humidity 

10 ... 90 %, no condensation at the rear of 

the device 

 

Atmospheric pressure, 

operation elevation 

1140 to 795 hPa 

Corresponds to an elevation 

of -1000 to 2000 m 

Pollutant concentration  SO

2

: < 0.5 vpm; 

Relative humidity < 60 %, 

no condensation at the rear of the device 

Test: 10 cm

3

/m

3

; 10 days 

H

2

S: < 0.1 vpm;  

Relative humidity < 60 %, 

no condensation at the rear of the device 

Test: 1 cm

3

/m

3

; 10 days 

Note the information in section "Safety instructions and further information (Page 10)" and 

the information on the mounting positions: 

 

Permitted mounting positions of the built-in units (Page 14) 

Содержание SIMATIC Industrial Flat Panel IFP2200











































Отзывы: