background image

Operation sequence

The operation sequence that follows 
describes the control using the hand-held 
control pendant. Operation over a 
communication channel is the same except 
for manual cable connection steps.

1.  Connect the hand-held control pendant 

cable plug to the receptacle for the 
appropriate controller compartment. 
With the isolating switch in the OPEN/
DISCONNECT position, the green LED 
will illuminate. Before proceeding to 
switch to the CLOSE/CONNECT position, 
verify the following:

• 

High-voltage compartment door is 
closed and latched.

• 

Contactor is in the OPEN position.

• 

Lever for manual operation has been 
dismounted.

2.  Press the pushbutton for the CLOSE/

CONNECT position. Please note it is not 
necessary to hold the button down. 
When the isolating switch begins to 
move, the green LED (for OPEN/
DISCONNECT position) will turn off and 
the red LED (for CLOSE/CONNECT 
position) will start to blink until the 
isolating switch reaches the CLOSE/
CONNECT position. 

3.  Once the isolating switch reaches the 

CLOSE/CONNECT position, the red LED 
(for CLOSE/CONNECT position) will 
illuminate. 

4.  With the isolating switch in CLOSE/

CONNECT position, it is possible to 
close and open the contactor.

5.  To proceed to move the isolating 

switch to OPEN/DISCONNECT position, 
verify that the contactor is OPEN and 
the manual lever is dismounted. 

6.  Press the pushbutton for the OPEN/

DISCONNECT position. Please note it is 
not necessary to hold the button 
down. When the isolating switch 
begins to move, the red LED (for 
CLOSE/CONNECT position) will turn off 
and the green LED (for OPEN/
DISCONNECT position) will start to 
blink until the isolating switch reaches 
the OPEN/DISCONNECT position. 

7.  Once the isolating switch reaches the 

OPEN/DISCONNECT position, the green 
LED (for OPEN/DISCONNECT position) 
will illuminate.

8.  With the isolating switch in the OPEN/

DISCONNECT position, it is possible to 
open or close the contactor, or if 
needed, open the high-voltage 
compartment door.

Operation sequence

Instruction manual

 | SIERS Siemens Integrated Electrical Racking System

Содержание SIDS-T40026-00-4AUS

















Отзывы: