Siemens SCALANCE XR324-4M PoE Скачать руководство пользователя страница 19

Страница: 19 / 74

Description

3.6 LED display

SCALANCE XR-300M PoE
Compact Operating Instructions, 05/2016, A5E02661178-10

Definition of the fault mask

Using the fault mask, you specify an individual "good status" for the connected ports and the

power supply. Deviations from this status are then displayed as errors/faults.
1.

Turn on display mode A or D. Display mode A is active when the "DM" LED is not lit.

Display mode D is active when the "DM" LED flashes yellow/orange. If a different display

mode is active, you will need to press the SET/SELECT briefly (possibly several times)

until the required display mode is active.

Hold down the SET/SELECT button for five seconds. After three seconds, the "DM" LED

begins to flash. If you release the button before the five seconds have elapsed, the

previous fault mask will be retained.

Enable/disable the redundancy manager

Turn on display mode B. Display mode B is active when the "DM" LED is lit green. If a

different display mode is active, you will need to press the SET/SELECT briefly (possibly

several times) until display mode B is active.

Hold down the SET/SELECT button for five seconds. After three seconds, the "DM" LED

begins to flash. If you release the button before the five seconds have elapsed, the action

is aborted.

The result of the action depends on the initial situation:
–

If the redundancy manager and media redundancy were disabled, media redundancy

is also enabled after enabling the redundancy manager.

–

If you disable the redundancy manager, media redundancy remains enabled.

3.6

LED display

The "RM" LED for the "redundancy manager" function

The "RM" LED indicates whether or not the device is operating in the role of redundancy

manager and whether or not the ring is operating error-free.

LED color

LED status

Meaning

off

The device is not operating in the role of "redundancy manager".

green

The device is operating in the role of redundancy manager. The

ring is working without problems, monitoring is activated.

green

flashes

The device is operating in the role of redundancy manager. An

interruption has been detected on the ring and the device has

switched through.

Содержание SCALANCE XR324-4M PoE











































































Результаты поиска

Содержание SCALANCE XR324-4M PoE

Отзывы:

Похожие инструкции для SCALANCE XR324-4M PoE

Бренды по названию

Популярные бренды

Siemens SCALANCE XR324-4M PoE, Краткое руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR324-4M PoE

Отзывы:

Похожие инструкции для SCALANCE XR324-4M PoE

Бренды по названию

Популярные бренды