manualshive.com logo in svg

Siemens SCALANCE XR-300M PoE Series, Краткое руководство по эксплуатации

Поделиться
Скачать
Siemens SCALANCE XR-300M PoE Series Скачать руководство пользователя страница 57

Note
Safety extra-low voltage

The supply of the devices by PELV (Protective Extra Low Voltage) according to DIN VDE 0100-410 
or IEC 60364-4-41 is permitted when the generated nominal voltage does not exceed the 
voltage limits 25 VAC or 60 VDC.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Do not connect or disconnect cables to or from the device when a flammable or combustible 
atmosphere is present.

WARNING

EXPLOSION HAZARD

Do not press the SELECT/SET button when there is an explosive atmosphere.

WARNING

Suitable cables at high ambient temperatures in hazardous area

At an ambient temperature of ≥ 60 °C, use heat-resistant cables designed for an ambient 
temperature at least 20 °C higher. The cable entries used on the enclosure must comply with 
the IP degree of protection required by EN IEC / IEC 60079-0, GB 3836.1.

WARNING

Unsuitable cables or connectors

Risk of explosion in hazardous areas
• Only use connectors that meet the requirements of the relevant type of protection.
• If necessary, tighten the connector screw connections, device fastening screws, grounding 

screws, etc. according to the specified torques.

• Close unused cable openings for electrical connections.
• Check the cables for a tight fit after installation.

Connecting up

6.7 Power supply

SCALANCE XR-300M PoE
Compact Operating Instructions, 03/2022, A5E02661178-15

57

Содержание SCALANCE XR-300M PoE Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды