Siemens SCALANCE X408-2 Скачать руководство пользователя страница 43

Страница: 43 / 52

Technical specifications

7.1 SCALANCE X414-3E and X408-2 - technical specifications

SCALANCE X-400
Compact Operating Instructions, 10/2013, A5E01020054-06

Cascading depth

SCALANCE X414-3E

SCALANCE X408-2

Linear/star structure

Any (only depending on signal

propagation time)

Any (only depending on signal

propagation time)

Ring with redundancy manager

in HRP mode

50 (for reconfiguration time <

0.3 seconds)

50 (for reconfiguration time <

0.3 seconds)

Switching properties

SCALANCE X414-3E

SCALANCE X408-2

Max. number of learnable

addresses

8000

Aging time (default)

40 s

Switching technique

Store and forward

Latency (store and forward time) 5 µs

5 µs

(10 µs when changing from

gigabit to Fast Ethernet or vice

versa)

Full wire speed switching

Number of frames

At a frame length of (in bytes):

at 100 Mbps

at 1000 Mbps

148810

1488095

84459

844595

128

45290

452899

256

23496

234962

512

11973

119732

1024

9615

96154

1280

8127

81274

1518

Note
The IE Switches X-400 support full wire speed switching complying with IEEE 802.3 on all

ports.
The number of packets depends on the packet length according to the IEEE802.3 standard.

Содержание SCALANCE X408-2





















































Результаты поиска

Содержание SCALANCE X408-2

Отзывы:

Похожие инструкции для SCALANCE X408-2

Бренды по названию

Популярные бренды

Siemens SCALANCE X408-2, Краткое руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X408-2

Отзывы:

Похожие инструкции для SCALANCE X408-2

Бренды по названию

Популярные бренды