Siemens SCALANCE X005 Скачать руководство пользователя страница 5

Страница: 5 / 38

SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01

Introduction

1.1

On the Operating Instructions

Purpose of the Operating Instructions

These operating instructions support you when commissioning the unmanaged Industrial

Ethernet entry level switches SCALANCE X005 and SCALANCE X005TS (Transportation

System).

Validity of the Operating Instructions

These operating instructions are valid for the following devices:

Device

Order number

SCALANCE X005

6GK5005-0BA00-1AA3

SCALANCE X005TS

6GK5005-0BA00-1CA3

Further documentation

The "SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks" manual

contains additional information on other SIMATIC NET products that you can operate along

with the SCALANCE X005 and SCALANCE X005TS IE switches in an Industrial Ethernet

network.
You can order the manual "SIMATIC NET Industrial Twisted Pair and Fiber Optic Networks",

release 05/2001, using the following order numbers:

6GK1970-1BA10-0AA0 German

6GK1970-1BA10-0AA1 English

6GK1970-1BA10-0AA2 French

6GK1970-1BA10-0AA4 Italian
You will also find this network manual on the Internet pages of Service & Support under the

following entry ID: 1172207 (

http://support.automation.siemens.com/WW/view/en/1172207

You will find further information in the "System Manual Industrial Ethernet" in the Manual

Collection.
You will find further information on the SCALANCE system on the Internet at

www.siemens.com/scalance (

www.siemens.com/scalance

Audience

These Operating Instructions are intended for persons who commission networks with the IE

switches of the SCALANCE X-000 product line.

Содержание SCALANCE X005







































Результаты поиска

Содержание SCALANCE X005

Отзывы:

Похожие инструкции для SCALANCE X005

Бренды по названию

Популярные бренды

Siemens SCALANCE X005, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X005

Отзывы:

Похожие инструкции для SCALANCE X005

Бренды по названию

Популярные бренды