Siemens SCALANCE X005 Скачать руководство пользователя страница 30

Страница: 30 / 38

Technical specifications

SCALANCE X005 / X005TS

Operating Instructions, 07/2014, C79000-G8976-C344-01

Technical specifications
Operating altitude

During operation

≤

2,000 m above sea level at max. 46

℃

ambient

temperature

≤

2,000 m above sea level at max. 40

℃

ambient

temperature

Design, dimensions and weight
Immunity

EN 61000-6-2 (Class A)

EN 61000-6-1 (Class B) with a ferrite core on the cables

Manufacturer: Würth Elektronik - Type: 742 711 31

RF interference level

EN 61000-6-4

Degree of protection

IP30

MTBF (EN/IEC 61709, 40 °C)

167.1 years

Housing material

Basic housing

Die cast aluminum, powder coated

Front cover

Polyphenylene ether + polystyrene (PPE+PS plastic)

Weight

550 g

Dimensions (W x H x D)

44 x 125 x 124 mm

Installation options

•

Mounting on a DIN rail

•

Mounting on an S7-300 standard rail

•

Wall mounting

Switching properties
Aging time

375 seconds

Max. number of learnable MAC

addresses

1024

Response to LLDP frames

Blocking

Response to spanning tree BPDU

frames

Forwarding

QoS priority queues

Note
The number of connected SCALANCE X Industrial Ethernet Switches influences the frame

propagation time.

When a frame passes through the SCALANCE X005 or SCALANCE X005TS, it is delayed

by the store and forward function of the switch:

•

with a 64 byte frame length by approx. 10 µs (at 100 Mbps)

•

with a 1500 byte frame length by approx. 130 µs (at 100 Mbps)

This means that the more SCALANCE X005 or SCALANCE X005TS devices the frame

passes through, the longer the frame delay.

Содержание SCALANCE X005







































Результаты поиска

Содержание SCALANCE X005

Отзывы:

Похожие инструкции для SCALANCE X005

Бренды по названию

Популярные бренды

Siemens SCALANCE X005, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X005

Отзывы:

Похожие инструкции для SCALANCE X005

Бренды по названию

Популярные бренды