Siemens RUGGEDCOM RST2228 Скачать руководство пользователя страница 13

Страница: 13 / 50

RUGGEDCOM RST2228

Installation Guide

Chapter 2

Installing the Device

General Procedure

Installing the Device

This chapter describes how to install the device, including mounting the device, connecting power, and

connecting the device to the network.

DANGER!

Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing

any maintenance tasks, make sure all power to the device has been disconnected and wait

approximately two minutes for any remaining energy to dissipate.

WARNING!

Radiation hazard – risk of serious personal injury. This product may contain a laser system and is

classified as a

CLASS 1 LASER PRODUCT

. Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation exposure.

IMPORTANT!

This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall

render all warranties null and void.
Changes or modifications not expressly approved by Siemens Canada Ltd could invalidate

specifications, test results, and agency approvals, and void the user's authority to operate the

equipment.

IMPORTANT!

This product should be installed in a

restricted access location

where access can only be gained by

authorized personnel who have been informed of the restrictions and any precautions that must be

taken. Access must only be possible through the use of a tool, lock and key, or other means of security,

and controlled by the authority responsible for the location.

CONTENTS

•

Section 2.1, “General Procedure”

•

Section 2.2, “Unpacking the Device”

•

Section 2.3, “Mounting the Device”

•

Section 2.4, “Connecting the Failsafe Alarm Relay”

•

Section 2.5, “Connecting Power”

Section 2.1

General Procedure

The general procedure for installing the device is as follows:

Содержание RUGGEDCOM RST2228



















































Результаты поиска

Содержание RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для RUGGEDCOM RST2228

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RST2228, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для RUGGEDCOM RST2228

Бренды по названию

Популярные бренды