manualshive.com logo in svg

Siemens RUGGEDCOM RST2228, Руководство по установке

Поделиться
Скачать
Siemens RUGGEDCOM RST2228 Скачать руководство пользователя страница 18

Chapter 2

Installing the Device

RUGGEDCOM RST2228

Installation Guide

12

Connecting Power

1

2

Figure 7: Assembling the Failsafe Alarm Relay Terminal Block

1.

 Pluggable Terminal Block   

 

2.

 Screw-Type Terminal Block

2. Connect a failsafe device to the terminal block.

5

1

4

4

5

3

2

3

Figure 8: Failsafe Alarm Relay Wiring

1.

 Pluggable Terminal Block   

 

2.

 Screw-Type Terminal Block   

 

3.

 Normally Open Terminal   

 

4.

 Common Terminal   

 

5.

 Normally Closed

Terminal

Section 2.5

Connecting Power

The RUGGEDCOM RST2228 supports dual redundant AC and/or DC power supplies that can be installed in any

combination.
The RUGGEDCOM RST2228 can be equipped with either a screw-type or pluggable terminal block, which provides

power to both power supplies. The screw-type terminal block is installed using Phillips screws and compression

plates, allowing either bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable

connections under severe shock or vibration.

Содержание RUGGEDCOM RST2228



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды