Siemens RUGGEDCOM M969F Скачать руководство пользователя страница 19

Страница: 19 / 56

RUGGEDCOM M969F

Installation Guide

Chapter 2

Installing the Device

General Procedure

Installing the Device

This chapter describes how to install the device, including mounting the device, connecting power, and

connecting the device to the network.

WARNING!

Radiation hazard – risk of serious personal injury. This product contains a laser system and is classified

as a

CLASS 1 LASER PRODUCT

. Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

DANGER!

Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing

any maintenance tasks, make sure all power to the device has been disconnected and wait

approximately two minutes for any remaining energy to dissipate.

IMPORTANT!

This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall

render all warranties null and void.
Changes or modifications not expressly approved by Siemens Canada Ltd could invalidate

specifications, test results, and agency approvals, and void the user's authority to operate the

equipment.

IMPORTANT!

This product should be installed in a

restricted access location

where access can only be gained by

authorized personnel who have been informed of the restrictions and any precautions that must be

taken. Access must only be possible through the use of a tool, lock and key, or other means of security,

and controlled by the authority responsible for the location.

CONTENTS

•

Section 2.1, “General Procedure”

•

Section 2.2, “Unpacking the Device”

•

Section 2.3, “Mounting the Device”

•

Section 2.4, “Connecting the Failsafe Alarm Relay”

•

Section 2.5, “Connecting Power”

Section 2.1

General Procedure

The general procedure for installing the device is as follows:

Содержание RUGGEDCOM M969F

























































Результаты поиска

Содержание RUGGEDCOM M969F

Отзывы:

Похожие инструкции для RUGGEDCOM M969F

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM M969F, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM M969F

Отзывы:

Похожие инструкции для RUGGEDCOM M969F

Бренды по названию

Популярные бренды