background image

5/8 

Siemens 

Room temperature controllers 

CE1N3036en 

Building Technologies 

 

13.10.2008 

Notes 

The room temperature controller should be mounted in a location where the air tem-
perature can be measured as accurately as possible without getting adversely affected 
by direct solar radiation or other heat or refrigeration sources. 

Mounting height is about 1.5 m above the floor. 

 

The unit can be fitted to a recessed conduit box. 

 

Only authorised staff may open the controller. 

Caution: The switching output voltage is from AC24V up to AC250V

 

 

The cables used must satisfy the insulation requirements with regard to mains 
potential 

 
When mounting the unit, fix the baseplate first. Then, make the electrical connections 
and fit and secure the cover (also refer to separate Mounting Instructions). 
The controller must be mounted on a flat wall and in compliance with local regulations. 
If there are thermostatic radiator valves in the reference room, they must be set to their 
fully open position. 

 

The controller is maintenance-free. 
 
If the temperature on the display does not agree with the room temperature effectively 
measured, the temperature sensor can be recalibrated. For that purpose both buttons 

+

 

and 

 must be pressed simultaneously for 3 seconds. Then, the temperature 

displayed can be changed by a maximum of +/- 10 K by pressing the  

+

 

and

-

 

but-

tons. Five seconds after the last push of a button, the controller will automatically return 
to the normal operational status. 
 
The setpoint limitation is used in some specific applications where the setpoint tem-
perature is required to be above 35°C (Less than 60°C).  For that purpose both buttons 

+

 

and

-

 

 must be pressed simultaneously for 5 seconds. The top row of the LCD will 

then display 35°C to signify the default setpoint limitation whereas the bottom row will 
display 

SPLt 

to signify the setpoint limitation mode.  The temperature limitation can be 

changed by pressing the 

+

 

and

-

 

buttons.  Five seconds after the last push of a but-

ton, the controller will automatically saved the value and return to the normal opera-
tional status.  
 
If the battery symbol appears, the battery power is almost exhausted and the batteries 
should be replaced. Only AAA alkaline batteries have to be used. 

To reset, first press and hold the button  , then press the two buttons 

+

-

 simultane-

ously for 3 seconds. All individual settings will be reset to their standard values. 

 

Mounting, installa-
tions and commis-
sioning 

Maintenance 

Sensor calibration 

Setpoint limitation 

Change of batteries 

Reset 

Содержание RDE20.1









Отзывы: