manualshive.com logo in svg

Siemens POWERMOBIL, Руководство пользователя, Страница: 10 / 36

Поделиться
Скачать
Siemens POWERMOBIL Скачать руководство пользователя страница 10

POWERMOBIL

 

SPR2-240.841.01

Page 2 of 12

Siemens AG

 

Rev. 01

05.03

CS PS 24

Medical Solutions

2 - 2

Disassembly

 

Covers

2

•

Remove the cover of the basic unit. At the same time disconnect the ground wire con-
nection. (See chapter 1 in the POWERMOBIL service manual.)

•

Remove the front C-arm cover from the X-ray image intensifier side of the C-arm (Fig. 2).

•

Remove the POWERPHOS cover (lateral paneling screws). 
(See chapter 1 in the POWERMOBIL service manual.)

•

Remove the cover of the horizontal carriage.
- For this purpose, release 3 screws on each side (1/Fig. 3).
- Release the plug-in connections for the brake keypad and the Emergency Stop switch.
- Remove the protective ground wire from the cover.

Fig. 3

Risk of injuries!
If not observed, slight to medium physical injuries and/or material 
damage can occur.

The C-arm cover contains counterweights and weighs > 10 kg.
Firmly hold the C-arm cover when removing.

Before releasing the C-arm cover make sure that the C-arm is in 
orbital center position.

If POWERPHOS and X-ray image intensifier are still attached to 
the C-arm, do not move the C-arm to the orbital end positions 
after loosening the C-arm cover.

WARNING

Содержание POWERMOBIL





































Отзывы:

Нет отзывов