Siemens MICROMASTER Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 78

background image

COMBIMASTER & MICROMASTER Integrated

REFERENCE MANUAL

©

Siemens plc. 1999

| G85139-H1731-U300-D2

32

Parameter

Function

Range

[Default]

Description / Notes

P081

Nominal frequency for
motor (Hz)

0 -

fmax**

[

!!!

]

P082

Nominal speed for
motor (RPM)

0 - 9999

[

!!!

]

P083

Nominal current for
motor (A)

0.1 - 99.9

[

!!!

]

COMBIMASTER: These parameters are set in the factory
and should not be changed under normal circumstances.

MMI : Motor data should be entered here

P084

Nominal voltage for
motor (V)

0 – 1000

[

!!!

]

P085

Nominal power for
motor (kW/hp)

0-100.0

[

!!!

]

.

P086

••••

Motor current limit (%)

0 - 250

[150]

The motor current can be limited with this parameter. If the
set value is exceeded, the output frequency is reduced until
the current falls to this limit. During this process, both LEDs
will flash

(see Operating Information, Section 5)

.

P087

Motor PTC enable

0 - 1

[0]

Change this parameter only when the PTC option is fitted.

0

= Disabled

1

= Motor PTC enabled

If P087 =

1

and the Motor PTC input goes high then the

inverter will trip (fault code F004). Note that if the internal
PTC gets too hot, the inverter will trip (fault code F005).

PTC Thresholds : Not tripped :<1k5

Ω

Typical Trip : >9k

Ω

Guaranteed trip : >25k

Ω

P089

••••

Stator resistance (

Ω

)

0.01-

100.00

[

!!!

]

COMBIMASTER :Set in the factory.

Do not adjust!

MMI : Set for value for Siemens motor. Adjust if required for
other motors

P091

••••

Serial link slave
address

0 - 30

[0]

Up to 31 COMBIMASTERS can be connected via the serial
link and controlled by a computer or PLC using the USS
protocol. This parameter sets a unique address for the
inverter.

Motor Current Limit - Overload Time to trip

160

150

140

130

120

115

113

100

105

110

115

120

125

130

135

140

145

150

155

160

165

0

30

60

90

120

150

180

210

240

270

300

330

Tim e/Seconds

Overload/%

110% and below will run forever

150% and above will trip in one minute

At 111% the drive will trip after 28 minutes

«
...
31
32
33
34
35
...
»

Содержание MICROMASTER















































































Отзывы:

Нет отзывов

Похожие инструкции для MICROMASTER

MINAS A5 Series

Бренд: Panasonic Страницы: 19

Бренд: Fagor Страницы: 60

Бренд: IBM Страницы: 66

Бренд: ZF-DUOPLAN Страницы: 37

TRINORM 436 Series

Бренд: Emerson Страницы: 6

Бренд: Siemens Страницы: 168

Бренд: Siemens Страницы: 186

Sinamics GM150 6SL3835-2LN44-2AA0

Бренд: Siemens Страницы: 238

SINAMICS PM240-2

Бренд: Siemens Страницы: 144

Бренд: Siemens Страницы: 520

SINAMICS PERFECT HARMONY GH180

Бренд: Siemens Страницы: 538

Бренд: Siemens Страницы: 680

Бренд: Siemens Страницы: 1288

RolloTron Pro Star Series

Бренд: RADEMACHER Страницы: 72

Rolltron PRO comfort

Бренд: RADEMACHER Страницы: 76

Бренд: RIB Страницы: 44

Бренд: Insignia Страницы: 92

VLT Active Front End AFE 302

Бренд: Danfoss Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды