Siemens INOX PRO SIMATIC IFP1900 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 25

background image

Replacing the seal of the compartment cover

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

8

Service Manual, 11/2017, A5E35751762-AC

1.

Remove the six screws of the terminal compartment cover.

2.

Remove the terminal compartment cover.

CAUTION

Do not drop the terminal compartment cover
Dropping the terminal compartment cover may result in minor injuries or damages to the

device.
Prevent the terminal compartment cover from dropping, especially when it is mounted

on a stand or support arm.

3.

Remove the seal of the terminal compartment cover.

4.

Insert the spare seal as shown in the figure.

5.

Check the seal for correct seat; make sure that the bore holes of the seal enclose the

collar of the press-fit components, see marked locations.

6.

Place the terminal compartment cover on the terminal compartment and reinsert the

six screws.

7.

Tighten all six screws with a torque of 3.5 Nm.

«
...
6
7
8
9
10
...
»

Содержание INOX PRO SIMATIC IFP1900


























Отзывы:

Нет отзывов

Похожие инструкции для INOX PRO SIMATIC IFP1900

Бренд: Oemtools Страницы: 4

Бренд: Samsung Страницы: 13

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Raymarine Страницы: 154

Бренд: Wells-Gardner Страницы: 25

Бренд: 4B Страницы: 16

Бренд: NEC Страницы: 2

Бренд: Siko Страницы: 12

Бренд: Alienware Страницы: 57

Бренд: Westinghouse Страницы: 4

AEROLYTE PRN 6060-A

Бренд: Zero Страницы: 33

Бренд: DBI SALA Страницы: 32

Бренд: NCR Страницы: 10

Бренд: Harmonic Drive Страницы: 58

Бренд: MSW Страницы: 19

Бренд: GVision Страницы: 15

Бренд: ViewSonic Страницы: 18

Бренд: NCI Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды