Siemens INOX PRO SIMATIC IFP1900 Скачать руководство пользователя страница 24

Страница: 24 / 25

Accessories and spare parts

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

Service Manual, 11/2017, A5E35751762-AC

Service pack 2, use only in combination with this service manual
The service pack 2 contains:

●

1 spare seal for the rear panel of the device

●

4 spare screws for the rear panel of the device

●

1 spare seal for the mechanical interface of the device

●

4 screws for fastening the stainless steel tube with flange from a mounting kit to the

mechanical interface of the device

●

1 connecting terminal for the power supply

●

Documentation

Article number 6AV7675-1JD21-0AA0

Service pack 3, in connection with devices for support arm mounting
Service pack 3 contains:

●

1 spare seal for the connection compartment cover of the device

●

1 spare seal for the mechanical interface of the device

●

1 spare seal for support arm mounting

●

8 screws M5 x 20 mm for support arm mounting

●

6 screws for the connection compartment cover of the device

●

1 connecting terminal for the power supply

●

1 terminal block for the terminal strip in the connection compartment

●

Documentation

Article number 6AV7675-1JD20-1AA0

Spare parts for devices with operator controls

The table below shows the order numbers of the operator controls on the front made by

Schlegel (

http://www.schlegel.biz

Operator control

Schlegel order number

EMERGENCY OFF pushbutton

EMERGENCY OFF switching element

RXUVP

PTFPOO

Illuminated pushbutton

Illuminated pushbutton switching element

RRJVAFT_682

CZTLP_505

LED red

LED green

L5, 5K24UR
L5, 5K24UG

Содержание INOX PRO SIMATIC IFP1900


























Результаты поиска

Содержание INOX PRO SIMATIC IFP1900

Отзывы:

Похожие инструкции для INOX PRO SIMATIC IFP1900

Бренды по названию

Популярные бренды

Siemens INOX PRO SIMATIC IFP1900, Руководство по обслуживанию

Результаты поиска

Содержание INOX PRO SIMATIC IFP1900

Отзывы:

Похожие инструкции для INOX PRO SIMATIC IFP1900

Бренды по названию

Популярные бренды