Siemens Gigaset M 101 Data Скачать руководство пользователя

Страница: 6 / 37

gigam101.fm5

21.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

Approval and conformity

Your Siemens Gigaset M101 Data has been certified by the Ger-

man Federal Office of Telecommunication Approval (BZT). This

equipment has been approved in accordance with the EU direc-

tive 91/263/EC Telecommunication Terminals.

This data terminal complies with the requirements of the EU di-

rectives:

Notes on PC and modem operation

Notes on Gigaset Repeater

89/336/EC

EMC Directive

72/23/EC

Low Voltage Directive

and thus carries the CE mark.

When using a modem, software malfunctions in the PC

(e.g. an operating system crash or program errors in the

application software) can prevent the cleardown of a

modem connection from a telephone line.

You incur

connection costs for trunk lines that you seize!

Since your Gigaset M101 Data only replaces a serial ca-

ble, malfunctions of this kind can also occur here. If such

a problem occurs, check the status of your modem and,

if applicable, reset it.
In the case of one-sided interruption of the mains supply

or complete interruption of your Gigaset M101 Data’s

hop, the interface’s status lines are reset to the initial

status in the partner station within 2 minutes (a modem

then clears down the connection).
Whenever possible, operate the station registered as

user at your PC (lokale Station), since any malfunctions

on the user side can be displayed, for technical reasons,

more quickly than at the base, see "LEDs and buttons"

on page 19.
Should the graphic or sound card be affected by interfer-

ence from Gigaset M101 Data, rotate Gigaset M101

Data until the interference is removed.

The Gigaset Repeater

cannot

be used to extend the

radio range.
The repeater was designed for use behind Gigaset 2000

base stations.

Содержание Gigaset M 101 Data






































Результаты поиска

Содержание Gigaset M 101 Data

Отзывы:

Похожие инструкции для Gigaset M 101 Data

Бренды по названию

Популярные бренды

Siemens Gigaset M 101 Data, Руководство по эксплуатации

Результаты поиска

Содержание Gigaset M 101 Data

Отзывы:

Похожие инструкции для Gigaset M 101 Data

Бренды по названию

Популярные бренды