Siemens Gigaset M 101 Data Скачать руководство пользователя

Страница: 32 / 37

Tips & tricks, settings

appendix.fm5

16.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

Sharing files

Since the Windows information given in the previous mask is

somewhat confusing, and since no references are made to the

File Manager/Explorer, here is the correct procedure. Once file

sharing has been activated and the PC restarted, you can re-

lease files for processing by the other PC via the File Manager/

Explorer.

To do this, start up Windows Explorer

Select the appropriate folder and then click

File

> Properties

The following mask containing the tabs

General

and

Sharing

ap-

pears:

Assign rights for the other PC users on your hard disk or set a

password to prevent access.

Files that support sharing are identified as follows:

1 Error in Windows help: the

Properties

submenu is not de-

scribed.

shared

not shared

Содержание Gigaset M 101 Data






































Результаты поиска

Содержание Gigaset M 101 Data

Отзывы:

Похожие инструкции для Gigaset M 101 Data

Бренды по названию

Популярные бренды

Siemens Gigaset M 101 Data, Руководство по эксплуатации

Результаты поиска

Содержание Gigaset M 101 Data

Отзывы:

Похожие инструкции для Gigaset M 101 Data

Бренды по названию

Популярные бренды