Siemens Gigaset M 101 Data Скачать руководство пользователя

Страница: 24 / 37

Tips & tricks, settings

appendix.fm5

16.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

Tips & tricks, settings

This section describes settings, implementation options and

programming methods.

Operating from a local station with two remote stations:

Please note that

●

Only one connection can be active.

●

Only one "Teilnehmer" station type can be registered at a

base that is ready for registration.

●

The station type for Gigaset M101 Data units is set to "Basis"

by default.

Perform registration as described in the section "Initial configu-

ration" on page 11.

The Gigaset unit connected to the PC is called "Gigaset 1" and

is the lokale Station. It is now an Teilnehmer

station type

and

your Gigaset 2 (Partnerstation) is a Basis. Configure the trans-

mission parameters that are required for a connection between

Gigaset 1 and Gigaset 2.

Change to the Local station tab and click

Change station type

your Gigaset 1 is now a base.

Exit the configuration program and connect Gigaset 3 to the

COM port.

Now start the "

Gigaset M101 Data

Set Gigaset

" configuration

program and switch to the Local station tab. Click

Change sta-

tion type

. Gigaset 3 is now an "Teilnehmer".

Press the black button on Gigaset 1 (station type currently Ba-

sis) for 10 s. The LEDs start to blink alternately, the base is ready

for registration.

Click

Register

, enter the PIN (factory default "0000") and click

. You have now registered Gigaset 3 (as an

extension

) at

Gigaset 1 (the

base

Configure the transmission parameters that are required for a

connection between Gigaset 3 and Gigaset 1. Exit the configu-

ration program.

Connect Gigaset 1 to the COM port at the PC that you want to

use for bothway operation.

Teilnehmer

Basis

COM

Basis

COM

Teilnehmer

Basis

Содержание Gigaset M 101 Data






































Результаты поиска

Содержание Gigaset M 101 Data

Отзывы:

Похожие инструкции для Gigaset M 101 Data

Бренды по названию

Популярные бренды

Siemens Gigaset M 101 Data, Руководство по эксплуатации

Результаты поиска

Содержание Gigaset M 101 Data

Отзывы:

Похожие инструкции для Gigaset M 101 Data

Бренды по названию

Популярные бренды