Siemens FST020 Скачать руководство пользователя страница 81

Страница: 81 / 194

Setup

3.4 Inputs and outputs

FST020 Function manual
Function Manual, 09/2017, A5E42949526-AA

3.4.3.13

Alarm class

Description
Selection of alarm classes which impact the status output. Each diagnostic event is allocated

to an alarm class. Applicable if Status mode = Alarm class and Status icons = Standard.
Bit 0: Process value alarm (PA)

Bit 1: Process value warning (PW)

Bit 2: Maintenance alarm (MA)

Bit 3: Maintenance warning (MW)

Bit 4: Maintenance required (MR)

Bit 5: Function check (FC)

Setting Maintenance alarm; Function check; Process value alarm; Process value warning; Mainte-

nance demanded; Maintenance required; None

Default

Path

Setup

→

Inputs and outputs

→

Channel 3 - relay

→

Alarm class

3.4.3.14

NAMUR status signal

Description
Selection of NAMUR status signals which impact the status output. Each diagnostic event is

allocated to a NAMUR status signal. Application if Status mode = Alarm class and Status

icons = NAMUR

Setting Failure; Function Check; Out of specification; Maintenance Required
Default None

Path

Setup

→

Inputs and outputs

→

Channel 3 - relay

→

NAMUR status signal

3.4.3.15

Polarity

Description
Logical polarity of status output.

Setting Active high level; Active low level
Default Active high level

Path

Setup

→

Inputs and outputs

→

Channel 3 - relay

→

Polarity

Содержание FST020



































































































































































































Результаты поиска

Содержание FST020

Отзывы:

Siemens FST020, Руководство по эксплуатации функций, Страница: 81 / 194

Результаты поиска

Содержание FST020

Отзывы: