Siemens FST020 Скачать руководство пользователя страница 176

Страница: 176 / 194

Communication

5.2 Modbus (Channel 1)

FST020 Function manual

174

Function Manual, 09/2017, A5E42949526-AA

Path

Communications

→

Service channel (USB)

→

MSD connect

5.2

Modbus (Channel 1)

5.2.1

Slave address (SW)

Description
The slave address (SW) for the Modbus device can be configured. This address is used if

the DIP switch is set to 0.

Setting 1 to 247
Default

Path

Communication

→

Modbus (Channel 1)

→

Slave address (SW)

5.2.2

Slave address (HW) (read only)

Description
The slave address (HW is determined by the DIP switch setting on the transmitter cassette

and can be read out in this parameter. This address is used if the DIP switch is set to a value

> 0.

Options Read only

Path

Communication

→

Modbus (Channel 1)

→

Slave address (HW)

5.2.3

Baud rate

Description
Baud rate of Modbus interface.

Setting 9600 Bit/s; 19200 Bit/s; 115200 Bit/s; 38400 Bit/s; 57600 Bit/s; 76800 Bit/s; 1200 Bit/s;

2400 Bit/s; 4800 Bit/s

Default

Содержание FST020



































































































































































































Результаты поиска

Содержание FST020

Отзывы:

Siemens FST020, Руководство по эксплуатации функций, Страница: 176 / 194

Результаты поиска

Содержание FST020

Отзывы: