Siemens FST020 Скачать руководство пользователя страница 138

Страница: 138 / 194

Maintenance and diagnostics

4.3 Maintenance

FST020 Function manual

136

Function Manual, 09/2017, A5E42949526-AA

4.2.8.3

149 - Transm. temp. below alarm limit

Description
This event can be mapped to an alarm class respective NAMUR status signal.

Setting Process value alarm (PA) resp. Out of specification; Maintenance alarm resp. Failure
Default Process alarm (PA) resp. Out of specification

Path

Maintenance and diagnostics

→

Diagnostic events

→

Assign alarm class

→

149 - Transm.

temp. below alarm limit

4.3

Maintenance

4.3.1

Copy configuration

Description
Copy configuration - copy configurations from the SensorFlash to the device.

Setting Cancel; OK
Default Cancel

Path

Maintenance and diagnostics

→

Maintenance

→

Copy configuration

4.3.2

Spare part replacement

4.3.2.1

Transmitter

4.3.2.1.1 Replace transmitter

Description
Only Siemens authorized personnel may replace spare parts.
Access level: Expert user only.

Setting Cancel; OK
Default Cancel

Содержание FST020



































































































































































































Результаты поиска

Содержание FST020

Отзывы:

Siemens FST020, Руководство по эксплуатации функций, Страница: 138 / 194

Результаты поиска

Содержание FST020

Отзывы: