Siemens CP 443-5 Extended Скачать руководство пользователя страница 27

Страница: 27 / 27

Technical Specifications

B4 - 27

CP 443-5 Extended for PROFIBUS / Manual Part B4
Release 6/2005

C79000-G8976-C162-06

Technical Specifications

General Technical Data

Table 7-1

Technical Data

Value

Supported Transmission Rates

9.6 Kbps, 19.2 Kbps, 45.45 Kbps

93.75 Kbps, 187.5 Kbps, 500 Kbps

1.5 Mbps, 3 Mbps, 6 Mbps, 12 Mbps

Interfaces

Attachment to PROFIBUS

9-pin D-sub female connector

Maximum current consumption on the PROFIBUS
interface with network components attached (for
example, optical network components)

100 mA at 5V

Power supply

5 V DC

Current consumption

- from S7-400 backplane bus

1.0 A typical at 5V

Power loss

5.5 W

Permitted ambient conditions

Operating temperature

Transportation/storage temperature

Relative humidity

Altitude

C to +60

- 40

C to +70

max. 95% at +25

up to 2000 m above sea level

Design

Dimensions W x H x D (mm)

25 x 292 x 200

Weight

approx. 800 g

All the information in /1/ in the Section “General Technical Data” regarding the
following topics also applies to the CP 443-5 Extended

Electromagnetic compatibility

Transportation and storage conditions

Mechanical and climatic ambient conditions

Insulation tests, class of protection and degree of protection

Содержание CP 443-5 Extended




























Результаты поиска

Содержание CP 443-5 Extended

Отзывы:

Бренды по названию

Популярные бренды

Siemens CP 443-5 Extended, Руководство пользователя

Результаты поиска

Содержание CP 443-5 Extended

Отзывы:

Бренды по названию

Популярные бренды