background image

1.3 Legal note

Legal note concept

This guide includes notes that must be followed to prevent damage to property.

Notes dealing only with damage to property use the signal word NOTICE and an
exclamation point.

They are depicted as follows:

NOTICE

Type and source of hazard

Consequences in the event the hazard occurs

Controls/prohibitions to prevent the hazard

Qualified personnel

Only qualified personnel may commission the device/system. Qualified personnel
for purposes refer to qualified due to training and experience to recognize and
avoid risks when working with this device/system.

Proper use

The device/system described here may only be used in building technical plants
and for the described applications only.

The trouble-free and safe operation of the device/system described here requires
proper transportation, correct warehousing, mounting, installation, commissioning,
operation, and maintenance.

You must comply with permissible ambient conditions. You must comply with the
information provided in the Section "Technical data" and notes in the associated
documentation.

Fuses, switches, wiring and grounding must comply with local safety regulations for
electrical installations. Observe all local and currently valid laws and regulations.

Exemption from liability

The content of this document was reviewed to ensure it matches the hardware and
firmware described herein. Deviations cannot be precluded, however, so that we
cannot guarantee that the document fully matches the actual device/system. The
information provided in this document is reviewed on a regular basis and any
required corrections are added to the next edition.

Safety

Legal note

1

6 | 170

A6V10733786_en_c

Содержание Climatix S300 HRV











































































































































































Отзывы: