manualshive.com logo in svg

Siemens Cerberus GW-21, Техническое руководство, Страница: 28 / 44

Поделиться
Скачать
Siemens Cerberus GW-21 Скачать руководство пользователя страница 28

24

Siemens Building Technologies

Cerberus Division

E1481b

06.2000

9.2 

Second case

In this configuration, the  LMS system sees the STT as a subsystem and it fully man-
ages it. Two lines are needed to connect the  STT to the gateway.
The 

first line

 is a slave line for the gateway (and a master line for the  STT), has to be

configured as a  CS11 subsystem on the gateway (see Section 4 for the proper setting)
but it must be configured as STT subsystem on  LMS.
The 

second line

 is a master line for the gateway (and a slave line for the STT), has to

be configured as STT subsystem on the gateway (see Section 4 for the proper setting)
and it must not be configured on LMS.
This configuration allows to connect a maximum of two  CS11 to the Gateway; both of
them can use the STT.
The address used for the first line (configured as STT on LMS) must be adjacent and
lower than the address used for the second line (that is not configured on LMS). The
two lines must be logically contiguous but not necessarily physically contiguous; i.e. if
there is one LMS that use UARTs 2, the first line can be on UART 1 and the second
line can be on UART 3. In this case they are not physically contiguous but are logically
contiguous (see examples below).

GW-21.xx

STT

CS11

CS11

Fig. 18 STT as a subsystem

Содержание Cerberus GW-21













































Отзывы:

Нет отзывов